How to troubleshoot a Keyboard and Mouse not detected

Ando Zonk share how to cope with a Keyboard and Mouse is not detected. This case may often experienced by many people. Here's how:

The cause of the Keyboard and Mouse are not detected:
1. The possibility of the keyboard or mouse is indeed damaged.
2. Possibility of keyboard or mouse port on the mainboard damaged.

For keyboard or mouse yg is broken, we just replace the keyboard or mouse aja yg the damaged

As for the keyboard or mouse port on the mainboard damaged yg there are several possibilities:

1. keyboard mouse Port is already loose, so the connection is not perfect. This can occur if we are often off the plug of the keyboard or the mouse.
The solution is to replace the keyboard mouse port.

2. Voltage 5 volts for power supply keyboard missing. Usually caused by parts with the symbol L yg breaking up. components with the symbol L is the same fuse. It is located around the keyboard port, usually behind him. This component checks, if damaged replace or directly connect the cable wire, wrote with 1 seed.

Or if you have trouble to replace chipnya, aja sharing connector USB to PS-2.

Good Jobs

How Resetter Epson SX400 and TX400

Good morning this time Ando Zonk will tell about how Resetter Epson SX400 and TX400. How Resetter Epson resetter software is using the TX400 TX400 and SX400. This Resster I have tried and succeeded.

How Resetter Epson SX400 and TX400

1. The first step of course epson SX400 and TX400 printer must be already installed drivers. To Download its driver in epson driver download

2. Download software resetter Epson SX400 TX400 and first. Software Resetter Epson named TX400 SX400, and you can download it here Click

3. Important!!! Turn off your Antivirus, because it detected resetter T13 modifications as viruses by antivirus.

4. run the program resetter Epson SX400 TX400 and with double click "URLoader.exe", do not directly at "URAdjProg.exe" because the program will not run if directly from "URAdjProg.exe"

See the image below:

Check: used to check maximum 7800 counter point, you can see it on the main pad counter. If more or close to 7800 points means the printer needs to be reset in the

Initialization: used to reset the printer counter back or mengenolkan

Once finished turn off printer and turn on again. The printer will be alive with lights in green. Means Epson printer and TX400 SX400 which blink last is ready to use again.

How to Service a Seagate hard drive eror

In fact I often find this case, namely the Seagate konslet hard disk. Konsletnya hard drive is causing the power supply also died or to the protectionism and any computer can not be turned on. You might have ever or are currently experiencing this, namely your seagate hard drive konslet, when a lot of data stored in the hard disk. How do I service the seagate konslet hard disk?

Here I will try sharing about how to service a hard drive seagate konslet.

Seagate hard drive causes a Konslet:
The presence of excess voltage of the power supply to the hard drive (Over Voltage)

Preparation Tool:

• Screwdriver Star: to open the screw board hard drive.
• The Multitester to check components: diodes damaged.
• Solder and lead: used to replace components damaged wrote.
• Spare part diode 1A-2A: buy at electronics.

How to Service a Seagate hard drive error:

• For the layout of the components are konslet hard drive is on the inside, you need to open a board inside the hard drive

• For the konselet hard drive components already seen directly, you do not need to open up the board.
• Konselet on harddisk Seagate this often happens at the safety voltage of 12 volt DIODES. Voltage 12 voltnya i.e. suply power cable which is yellow. While the voltage is 5 volts red wires. Sometimes a safety DIODE voltage 5 volts have also been konslet but rarely.

• Check the DIODE voltage safety voltnya 12. also check the DIODE 5 safety voltnya. look at the picture.
• Immediately replace the harddrive konselet diodes. with 1-2 Ampere diode, electronic shops to buy much. Note the position of the anode and cathode is. In fact by just removing the damaged diode without replacing them, your hard drive will be back to normal. In this way, however I do not recommend, because without the diode means without protection if there is over voltage/excess voltage.

How to open a File/Folder Access Denied

This time the post is about how to open the File/Folder Access Denied. The cause of the Folder/File Access Denied or can't be opened:  The file or Folder was created on an NTFS file system that changes the Security ID. Or you may never give the password on your Windows, then you do a reinstall of Windows. As a result there was a Folder/File Access Denied that cannot be opened.

How to open a File/Folder Access Denied:

• Open The Windows Explorer = > Click Tools = > > = View Folder Options
• Uncheck Use simple file sharing (Recommended) = > click OK

• Right click on folder locked: the example name of the folder "System Volume Information"]
• Select Properties = > Security. (If there are warning click OK)
• Click Advanced = > Owner = > will appear the following window:

• Click The User Name Administrator,
• Tick in lieu of the Owner of Subcontainer and Objects.
• Then Click OK/YES
• And finally your folders/files Access Denied will be opened again.

How to Self Test HP 3325 Printer, 3535, 3744, 3920, 3940, 2466

How to Self Test HP 3325 Printer, 3535, 3744, 3920, 3940, 2466
If you often get your printer and servisan are often difficult to test print for having to install all the drivers on your computer, you may need to try this trick.

Here is how to test direct print from printer without passing the computer.


How to print test direct from HP 3325 printer, 3535, 3744, 3920, 3940, 2466:

1. turn on the Printer.
2. press and hold the power button do not at release. (if released dead ...)
3. Then open the printer cover lid (the lid of the printer) 3 x-4 x (three-four times the open lid), do not get less, and the last closing condition, then the new powernya button is released.
HP printer and you will start to run a print test.

How To Self Test Canon DeskJet Printers

If you often get your printer and servisan are often difficult to test print for having to install all the drivers on your computer, you may need to try this trick.

Here is how to test direct print from printer without passing the computer.

How to print the test directly from the printer Canon IP1200, IP1300, IP1600, IP1700, IP1980, IP1880, etc.:



1. turn on the Printer.
2. Press resume button-press 4 x-5 x rapidly, do not get less.
3. canon printers And you will start to run a print test.

Prepare kertasnya first do not forget

To Self Test the Printer Canon Multifunction can directly pass the copy button on the printer.

How To Self Test The Printer HP2566

If you often get your printer and servisan are often difficult to test print for having to install all the drivers on your computer, you may need to try this trick.

Here is how to test direct print from printer without passing the computer.

How to print test direct from HP printer: 2566

1. turn on the Printer.
2. press and hold the power button do not at release. (if released dead ...)
3. Then press the arrow keys 4 x (three-four times) then new powernya button is released.

HP printer and you will start to run a test print

Do not forget to prepare your paper